Printing Inks and Substrates: Why the Same File Prints Differently

The same file, three printers, three different results

Anyone who has sent identical artwork to two suppliers knows the experience: the proofs come back and they are not the same. One is warmer, one is darker, the flat brand colour has drifted, and both printers insist their output is correct. Usually both are right, in the sense that each has printed accurately within its own process. What has changed is everything around the file — the ink chemistry, the paper, the press, the screening and the point at which the numbers in the file get turned into physical ink coverage.

The file itself contains no colour. It contains instructions. A CMYK value is a recipe expressed as percentages of cyan, magenta, yellow and black, and a recipe only produces a predictable dish if the ingredients and the oven are known. This article works through what actually varies between print jobs, why it varies, and what a buyer or designer can specify to bring the variation under control.

What the ink is doing

Printing is subtractive. Each ink layer absorbs part of the incoming light and reflects the rest, so adding inks removes light and moves towards black. This is the opposite of a screen, which emits light and adds towards white, and it is the root reason that vivid screen colours cannot always be printed.

Real inks are imperfect absorbers. A cyan ink that should absorb only red light also absorbs some green, and magenta absorbs more blue than it should. These impurities are why overprinting cyan, magenta and yellow at full strength yields a muddy dark brown rather than a clean black, and why a black ink is added to the set. They also constrain the achievable gamut, which is smaller than most designers assume.

Ink families and where they differ

  • Offset lithographic inks. Thick, tacky, oil-based pastes transferred through a water-based dampening system. They sit largely on the surface of coated stock and soak into uncoated stock. The workhorse of commercial print.
  • Ultraviolet and LED-cured inks. Cured instantly by exposure to ultraviolet light rather than by absorption and oxidation. They stay on the surface, so colours are typically more vivid on absorbent stock, and the finished sheet can be handled immediately.
  • Aqueous and dye-based inkjet. Very wide gamut, especially in blues and greens, which is why photographic inkjet output can look richer than offset. Dye inks are more vulnerable to light and moisture than pigment inks.
  • Pigment inkjet. More lightfast and more stable, at the cost of slightly reduced saturation and a greater tendency towards a phenomenon called bronzing on glossy media.
  • Dry toner. Plastic particles fused to the sheet with heat. Toner sits on top of the surface and reflects light differently, which is why a toner sheet often looks slightly glossier and flatter than an offset sheet of the same colour.
  • Extended gamut sets. Adding orange, green and violet to the four process inks widens the reachable range considerably and lets a printer hit spot-ink brand colours without a dedicated ink.

What the substrate is doing

The paper is not a passive background. It is roughly half the optical system, and it is the largest single reason the same file prints differently.

  • Absorbency. Uncoated stock draws ink into the fibres, where it scatters and appears lighter and duller. The same ink on a coated sheet sits in a thin film on a sealed surface and looks markedly more saturated. The difference is easily the size of a noticeable colour shift.
  • Dot gain. A halftone dot spreads as ink is absorbed, so a 50 per cent tint can print as 65 per cent or more. Every process has a characteristic gain curve, and correcting for it is one of the main jobs of a press profile.
  • Base white. Papers are not the same white. Some are warm and creamy, some are neutral, and many are made bluer with optical brightening agents — fluorescent compounds that absorb ultraviolet and re-emit visible blue. Those papers look brilliantly white under daylight and duller under a lamp with no ultraviolet output, which means the same printed sheet genuinely changes appearance with the room.
  • Opacity and show-through. On thin stock, the image on the reverse side alters the apparent lightness of the front. Heavy solid coverage on the back of a page is visible as a subtle darkening on the front.
  • Surface finish. Gloss, silk and matte coatings change the ratio of specular to diffuse reflection. Matte coatings scatter light and reduce apparent contrast and saturation compared with gloss, using identical inks.
  • Non-paper substrates. Corrugated board, film, foil and textiles each bring their own absorbency, texture and base colour, and none of them behaves like a press sheet.

The separation decision nobody sees

A file supplied in a screen colour space has to be converted to the ink recipe at some point, and where that happens determines a great deal. If the designer converts, the designer controls it. If the file goes out untagged and the printer’s workflow converts it with a default setting, control has been surrendered to a preference in someone else’s software.

Even at identical colour appearance, there is no single correct set of ink percentages, because black ink can substitute for combinations of the other three. That trade-off is set by two parameters that are rarely discussed outside prepress.

Black generation

  • Grey component replacement. Where cyan, magenta and yellow overlap to form a neutral component, that component can be replaced by black ink. Heavier replacement means less total ink, faster drying, better neutral stability and cheaper running, but shadow areas can look thinner.
  • Under colour removal. A milder version applied mainly to the darkest tones, reducing ink build-up in shadows while leaving mid-tones alone.
  • Total area coverage. The sum of all four percentages in the darkest region, capped by the process. A web-fed newspaper press may allow only around 240 per cent, while a sheetfed coated job may take 300 to 340. Sending a file built to a 340 limit into a 240 process guarantees smearing or a forced late conversion.
  • Rich black versus flat black. Large areas printed in black alone look washed out. A rich black adds supporting inks, but each supporting ink introduces a registration risk on fine reversed-out type.

Standards exist, and they work

The reason any of this is manageable is that the industry standardised the process rather than the equipment. Characterisation data sets describe what a well-run press of a given type produces on a given paper class, and profiles built from that data let a designer preview and convert reliably.

  • ISO 12647. The family of standards defining tone value increase, ink colour and grey balance for the main printing processes. A printer certified to the relevant part is committing to a defined target rather than to house taste.
  • Characterisation data. Reference sets such as those used for coated and uncoated European offset, and their successors built on newer measurement conditions, provide the numbers that profiles are derived from.
  • Measurement conditions. The M-series conditions define how the measuring instrument illuminates the sample, and specifically how it handles ultraviolet. On brightened papers, measurements under different conditions disagree, so the condition must be stated for any tolerance to mean anything.
  • Contract proofing. A proof produced on a calibrated device simulating the target press and paper, carrying a control strip that can be measured. This is the artefact that turns an argument into a measurement.

Spot colours, and why they still drift

Premixed spot inks exist precisely to escape process variation, and they help, but they are not immune. A spot ink is a physical mixture applied at a target film thickness, and film thickness varies across a press run. Slightly heavy ink laydown makes the colour darker and more saturated; slightly light makes it pale. Printers control this with a densitometer, but the tolerance is real.

Spot colours also change with substrate exactly as process inks do, which is why swatch books are published in separate coated and uncoated editions with visibly different results from the same ink. And swatch books fade: an old, sunlight-exposed book is no longer a reference, though it will be used as one until someone notices.

How to make the results converge

Most print colour disputes are avoidable, and the avoidance is procedural rather than technical.

  • Name the target. Specify the printing condition and paper class in the job brief, and supply files converted to that condition, or supply tagged files and state that conversion is the printer’s responsibility.
  • Specify brand colours in device-independent terms. Give CIELAB values with a tolerance and a measurement condition, plus per-substrate recipes. A single ink reference number is an instruction, not a specification.
  • Buy a proof for anything that matters. A measured contract proof approved by both parties converts opinion into a verifiable target, and it is cheaper than a reprint.
  • Judge under defined light. Compare proof and press sheet in a standardised viewing booth. Comparing under office lighting, especially with brightened papers, produces disagreements that no press adjustment can resolve.
  • Design within the process. If a colour sits outside the achievable range, no amount of press work will produce it. Soft-proof it before the design is approved rather than after.
  • Accept a tolerance. Print is a physical process with variation across a sheet and across a run. A specification with a realistic tolerance gets met; a demand for an exact match does not.

The file is a set of instructions, the press is an interpreter, and the paper is half the result. Once a job is specified that way — target condition, device-independent brand values, a measured proof and a stated tolerance — the mysterious variation between suppliers mostly stops being mysterious and becomes a set of differences that can be predicted, discussed and, where it matters, paid to remove.